GearCalc - Calculates the theoretical maximum speeds in each gear at various speeds, the Gear Calculation Chart and the maximum RPM at which you would need to accelerate to reach the calculated speed in that gear. - Pressing on the Full Screen button will switch to showing the calcs in full screen mode. - Shows the numerical gear ratios (reverse gear ratio is 1.18) - Shows the number of gears and the theoretical maximum RPMs in the redline and the differential gear ratio. - Shows the maximum speed you could reach in each gear if you had perfect gear engagement. - Shows the RPM values for every 10 Km/h increment in metric mode or every 5 MPH increment and gear up to the redline. - Shows the rev drop at each gear change. - Shows the theoretical maximum speed in each gear and the speed per 1000 RPM. - Shows the RPM values for every 10 Km/h increment in imperial mode or every 5 MPH increment and gear up to the redline. - Shows the rev drop at each gear change. - Shows the theoretical maximum speed in each gear and the speed per 1000 RPM. - Shows the RPM values for every 10 Km/h increment in metric mode or every 5 MPH increment and gear up to the redline. - Shows the rev drop at each gear change. - Shows the change in revs at each gear change. - Shows the RPM values for every 10 Km/h increment in imperial mode or every 5 MPH increment and gear up to the redline. - Shows the change in revs at each gear change. - Shows the revs for every 10 Km/h increment in metric mode or every 5 MPH increment and gear up to the redline. - Shows the change in revs at each gear change. - Shows the change in revs at each gear change. - Shows the RPM values for every 10 Km/h increment in imperial mode or every 5 MPH increment and gear up to the redline. - Shows the change in revs at each gear change. - Shows the change in revs at each gear change. - Shows the RPM values for every 10 Km/h increment in metric mode or every 5 MPH increment and gear up to the redline. - Shows the change in revs at each gear change. - Shows the change in revs at each gear change. - Shows the RPM values for every 10 Km/h GearCalc Crack + License Key Full Free Download GearCalc can be used for calculating engine speed during a race, shifting at the correct RPM for different models of cars, for choosing an appropriate gear set to maximise performance, estimating maximum speeds in top gear or bottom gear, calculating the rev drop at each gear change, and calculating approximate fuel economy. This section contains more detailed instructions on running the program. Instructions for running the software: File menu: The first menu provides options for loading a file, saving a file, opening or closing a file, and some options for editing information in a file. File menu: Load: The Load button opens the file selection dialog box. A dialog box will open when you click the File button (top right of the interface) and select "Load" from the Load list on the Open Dialog Box. If you press the open button, the file selected will be loaded. Save: The Save button allows you to save the results to a file for later reference. Open: The Open button allows you to open a file, which has been saved previously. Close: The Close button allows you to close the current window. Options: There are a few options that will be shown in the bottom of the screen, and you can adjust them by clicking on the arrows on the left. Exit: This button allows you to exit the program. Input Parameters: To begin inputting your parameters, press the [S]ave button and then select an option from the menu that appears. You may also press the Edit button to open a file with all your inputs already in place. After you input your information, you must save it. The first tab of the input file is the Input Data tab. Enter all data in here including the redline of the engine, the max RPM for the transmission, the differential ratio, and the tyre size. You can either use the default values in the defaults list or you can type in your own values. If the default values are entered in the defaults list, then they will be overwritten if the values in the input data are not the same as those in the defaults list. If you enter the same values in the defaults list as you enter into the input data, then they will remain after the Save button is clicked. Redline: The redline is the engine's max RPM. The maximum RPM that the engine can reach at any time. Max RPM: The max RPM is the maximum RPM of the engine at which the vehicle can reach (i.e. attain) without any RPM drop in the transmission, due to clutch slippage or the slipping of the friction plates on the flywheel. The max RPM value will either be the spec-rated RPM (the factory's estimate of the max RPM) or the user's 1a423ce670 GearCalc Crack + This routine sets the clutch and gear position when the shift key is pressed. The main purpose of this function is to set the gear position at a certain time, such as at start-up. This is also used to set a specific gear position, which can be used later when a corresponding “set clutch/set gear” routine is used. The user can also select a gear position to be set in later programs by selecting a gear position in this function, using this routine (located in program item[HANDLE_SHIFT]). Items that can be set in this function are: 1) When a gear is set: Set the clutch position using the program[HANDLE_CLUTCH] and the set a specific gear position. This is used in program item[HANDLE_TIMECLUTCH], where the user can use this function to set the set a specific gear position in program item[HANDLE_TIMECLUTCH] later. 2) Use when no gear is set: Set the clutch position using the program[HANDLE_CLUTCH] and set a neutral gear position. This is used in program item[HANDLE_TIMECLUTCH], where the user can set the use when no gear is set in program item[HANDLE_TIMECLUTCH] later. 3) Use when no clutch is pressed: Set the gear position using the program[HANDLE_CLUTCH] and set a neutral gear position. This is used in program item[HANDLE_TIMECLUTCH], where the user can use this function to set the use when no clutch is pressed in program item[HANDLE_TIMECLUTCH] later. Program item[HANDLE_SHIFT]: This function will set the gear position (using the clutch position set in the clutch function) when the shift key is pressed. The user can change the position in this function that the gear position will be set to, by setting the shift gear position using the program[HANDLE_SHIFT]. A shift gear position can be set in the function using the function key as well. KEYMACRO Example: /* Set the gear position for the start up routine (set the first gear) */ * PROCESS_SET_HANDLE_SHIFT(SHIFT_SET_ONE_HANDLE); What's New in the? System Requirements: Windows XP Home or Professional Windows Vista Home or Professional Windows 7 Home or Professional Mac OS X 10.5.x or later (Mac OS X 10.4.9 or later recommended for testing) Minimum Processor: Pentium 4 2.1 GHz Core 2 Duo 2.4 GHz Core 2 Quad 2.0 GHz Minimum Memory: 1 GB Recommended Processor: Pentium 4 3.0 GHz Core 2 Quad 3.0 GHz
Related links:
Kommentare